-- *****************************************************************
-- CISCO-IF-LINK-CONFIG-MIB.my: Interface Link Configuration MIB
--
-- March 2000, Subra Hegde
--
-- Copyright (c) 2000 by cisco Systems, Inc.
-- All rights reserved.
-- *****************************************************************CISCO-IF-LINK-CONFIG-MIB DEFINITIONS::=BEGIN
IMPORTSMODULE-IDENTITY,OBJECT-TYPEFROM SNMPv2-SMI
RowStatusFROM SNMPv2-TC
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
InterfaceIndexFROM IF-MIB
CiscoLocationSpecifier FROM CISCO-TC
ciscoMgmt FROM CISCO-SMI;ciscoIfLinkConfigMIB MODULE-IDENTITYLAST-UPDATED"200110050000Z"ORGANIZATION"Cisco Systems, Inc."CONTACT-INFO"Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-wanatm@cisco.com"DESCRIPTION"The MIB module for configuration of bulk distribution
(de-multiplexing of traffic from higher-bandwidth to
lower-bandwidth interfaces).
Terminology :
bulk-distribution : The bulk distribution is the
feature by which a line/interface
on one module can replace the line
for the other.
bulk-distribution module : The module which links its
interfaces to the target module.
target module : A module that gets incoming traffic
from a bulk distribution module
rather than from a back card.
The Module which supports bulk distribution, converts
traffic from its lines (may be T3, OC-N) to lines on
the target module (may be
T3, T1 etc). The bulk distribution is achieved by having a
point-to-point connection (bulk-distribution bus) between the
bulk-distribution module and the target module. The benefit
of bulk distribution is that the target module need not have
the back cards. The lines/interfaces from bulk-distribution
module will be used as lines for the target module.
An example is given here on linking interfaces.
|------------------------------------------------|
| |
| |------------------------------| |
| | | | | |
| | |-------------| | |
Ta|rget Module | | | | |
------- ------- ------- ---------------
| | | | | | | |
| | | | | | | |
| T1 | | T1 | |T1 | | Bulk |
|card | |card | |card | | Distribution |
| | | | | | | |
| | | | | | | Module |
| | | | | | | |
| | | | | | | (T3 card) |
| | | | | | | |
------- ------- ------- ---------------
"REVISION"200110050000Z"DESCRIPTION"Add object cilTargetModuleFramingType in cilConfTable table"REVISION"200009140000Z"DESCRIPTION"Initial version of this MIB module"
::={ ciscoMgmt 175}cilConfigMIBObjects OBJECTIDENTIFIER::={ ciscoIfLinkConfigMIB 1}cilConfig OBJECTIDENTIFIER::={ cilConfigMIBObjects 1}-- Interface Link configuration tablecilConfTable OBJECT-TYPESYNTAXSEQUENCEOF CilConfEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The interface link configuration table."::={ cilConfig 1}cilConfEntry OBJECT-TYPESYNTAX CilConfEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the cilConfTable. This entry is used for
linking an interface identified by cilSourceInterface
to an interface identified by cilTaregetModuleInterface.
The entries are created and deleted using the
cilRowStatus object. An interface on the bulk-distribution
module cannot be linked to multiple interfaces in the
target module."INDEX{ cilSourceInterface }::={ cilConfTable 1}
CilConfEntry ::=
SEQUENCE{
cilSourceInterface InterfaceIndex,
cilTargetModuleInterface CiscoLocationSpecifier,
cilRowStatus RowStatus,
cilTargetModuleFramingType INTEGER}cilSourceInterface OBJECT-TYPESYNTAXInterfaceIndexMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An interface of the bulk-distribution module (Source) which
will be linked with the interface of the target module. It
represents an entry in the ifTable."::={ cilConfEntry 1}cilTargetModuleInterface OBJECT-TYPESYNTAX CiscoLocationSpecifier
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Location of the managed entity on the target module.
Following is the supported format for this object and
all the values must be present.
shelf=<value>, slot=<value>, subSlot=<value> port =<value>.
The zero length value for this object is not supported."::={ cilConfEntry 2}cilRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION
"This object is used to create a new row or modify or delete
an existing row in the table. The cilTargetModuleFramingType
need not be specified to create a row. If cilTargetModuleFramingType
is not specified, a default value will be assumed as described in the
description of cilTargetModuleFramingType."::={ cilConfEntry 3}cilTargetModuleFramingType OBJECT-TYPESYNTAXINTEGER{notApplicable(1),dsx1D4(2),dsx1ESF(3)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object identifies the framing type of the target interface.
notApplicable(1) can not be set.
dsx1ESF Extended SuperFrame DS1 (T1.107)
dsx1D4 AT&T D4 format DS1 (T1.107)
Default value is dsx1ESF(3) if cilTargetModuleInterface is a T1 interface
and sonet/sdh byte-synchronous mapping is used on the cilSourceInterface.
Otherwise, the default value is notApplicable(1).
"::={ cilConfEntry 4}-- notifications-- conformance informationcilConfigMIBConformance OBJECTIDENTIFIER::={ ciscoIfLinkConfigMIB 3}
cilConfigMIBCompliances OBJECTIDENTIFIER::={ cilConfigMIBConformance 1}cilConfigMIBGroups OBJECTIDENTIFIER::={ cilConfigMIBConformance 2}cilConfigMIBCompliance MODULE-COMPLIANCESTATUSdeprecatedDESCRIPTION"The Compliance statement for interface link configuration group.
This has been replaced by the cilConfigMIBComplianceRev1 statement."MODULE-- this moduleMANDATORY-GROUPS{ cilConfMIBGroup }::={ cilConfigMIBCompliances 1}cilConfigMIBComplianceRev1 MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The Compliance statement for interface link configuration group.
This statement replaces cilConfigMIBCompliance statement."MODULE-- this moduleMANDATORY-GROUPS{ cilConfMIBGroupRev1 }OBJECT cilTargetModuleFramingType
MIN-ACCESSnot-accessibleDESCRIPTION"Required only for systems that support target interfaces
whose types are T1 and whose source interfaces are
sonet/sdh using byte-synchronous virtual tributary mapping."::={ cilConfigMIBCompliances 2}
-- units of conformancecilConfMIBGroup OBJECT-GROUPOBJECTS{
cilTargetModuleInterface,
cilRowStatus
}STATUSdeprecatedDESCRIPTION"These are objects related to interface link
configuration group. This group has been replaced
by cilConfMIBGroupRev1."::={ cilConfigMIBGroups 1}cilConfMIBGroupRev1 OBJECT-GROUPOBJECTS{
cilTargetModuleInterface,
cilRowStatus,
cilTargetModuleFramingType
}STATUScurrentDESCRIPTION"These are objects related to interface link
configuration group. This group replaces the
cilConfMIBGroup."::={ cilConfigMIBGroups 2}END